Tying the Egg Sucking Leech

Posted by  Tuesday, July 16 2013 7:00 am
expert

From Alaska to Arkansas, the Egg Sucking Leech without doubt is one of the top producing streamer flies to ever come out of a vise. As good as the traditional Wooly Bugger has been to fly anglers the Egg Sucking Leech is even better. The main reason for this patterns great success is its ability to be adapted to catch virtually any freshwater fish that exists. From trout to salmon and pike, the Egg Sucking Rabbit Strip Leech can just about do it all.

Just like other version of the bugger family, this fly was originally tied with black rabbit fur strips. More recently the Egg Sucking Leech has spawned an almost limitless amount of color combinations. Purple or natural rabbit fur variations have proven to be some of the more successful color combinations. This pattern is must have for any fly angler looking to fish spring runs of trout and salmon.

How to Fish It

Fishing the Egg Sucking Leech is relatively simple. If you are going to be fishing winter months or early season spring conditions with very cold water, cast this pattern to your target and let it dead drift drag-free down the river. Fish holding in cold temperatures become very lackadaisical and will not aggressively chase down your fly.

Using a slow delicate presentation with the Egg will help keep your fly in the strike zone longer providing you with a better chance of hooking into quality fish. In the spring and summer as the water temperatures gradually increase, fish will become more active and predacious. Cast your fly upstream of your desired target, let it sink for a few seconds and then give it three to four quick strips to get your retrieve started. Continue the fly working back to you by imparting short strips of line with intermittent pauses. This technique will get aggressive fish to chase and insatiably strike your fly.

Materials List

Hook Streamer Fly Hook Size 4
Thread Black/Red Uni Thread 8/0
Head Orange Bead
Tail Black Rabbit Fur Strip
Body Black Rabbit Dubbing
Rib Fine Silver Wire
Legs Pearl Flashabou
Collar Black Rabbit Fur Spun
Weight Lead Free Weight

 

Step-By-Step Tying Instructions

Step 1

Start this fly by sliding the colored bead on the hook shank small hole first and pushing it up to the hook eye. Place your hook into your vice and secure it into place tightly.

eggleech1

Step 2

Starting behind the bead wrap a small section of lead free weight onto the hook shank and wrap it down the hook until you reach the 1/2 way mark on the shank.

eggleech2

Step 3

Attach the black tying thread onto the hook just behind the bead and make a few wraps to keep the lead free weight in place securely. Cut six 3 inch strips of pearl flashabou and tie them down to the top of the hook shank extending off the back of the fly.

eggleech3

Step 4

Cut a three inch section of copper wire and tie it onto the hook shank at the 1/2 way point. Wrap this copper wire with the black thread down the hook shank until you reach the point above the barb.

eggleech4

Step 5

Select a three in section of Black Rabbit Fur Strip and tie the last one inch down at the point above the barb. Be sure to sweep the rabbit fur fibers forward while you are tying in this material.

eggleech5

Step 6

Dub the thread with the black rabbit dubbing and create a tapered body towards the back of the bead. It is going to take some time to build a nice thick firm body for the fly. Dub it one layer at a time until you have the thickness you are looking for.

eggleech6

Step 7

Pull the rabbit strip over the top of the body you just dubbed and tie it down directly behind the bead.

eggleech7

Step 8

Counter wrap the silver wire up the body of the fly in the opposite direction that you dubbed the body. Take care in working the wire through the rabbit strip so that you do not bind down to much of the fur fibers. It should take 5-6 wraps to get to the front of the fly.

eggleech8

Step 9

Create a dubbing loop with your tying thread and place about inch of rabbit strip fur into the loop. Spin the loop until a nice bushy fur hackle is created then wind this hackle around the hook behind the bead. As you wrap this fur hackle make sure to keep sweeping the fibers backward so that you do not unintentionally tie any fibers down. Make three or four wraps of thread back onto the now formed hackle collar to create swept look to the fly and then whip and cement the thread.

eggleech9
Tagged under
Read 2268 times
Last modified on Wednesday, August 14 2013 3:15 pm
Jason Akl
expert

Jason Akl is a writer, commercial fly tyer and guide with 15 years in the industry. Professionally, he's been a seasonal guide and fly tier that ties commercially and teaches tying classes to both adults and children. Most of his flies make their homes in fly shops in the northern Midwest but some have found their way as far as Europe. As a freelance writer, he's had many written pieces appear in both Canadian and American publications, as well as numerous global websites. When not on the bench or behind the computer, he spends time working with companies such as Daiichi Hooks or the American Tackle Co as part of their pro-staff doing product testing pieces and seminar

You must be signed in to post comments on Bass Pro Shops 1Source. Don't have an account? Please join Bass Pro Shops 1Source.
  • No comments found